This lightweight and compact microphone holder can be mounted on any guitar amplifier or cabinet. The clamp mechanism allows a firm and secure holding of the microphone while the flexible gooseneck allows you to find the perfect micing position. These features will guarantee for a faithful tone reproduction.
Perfect for amplifiers or monitor speakers. The support arms have a tilt angle of 42° and are height-adjustable. The stand is foldable for easy transport. Load capacity up to 35 kg. Wt: 4.1 kg, H: 425/515 mm, Support Width: 280 mm, D: 350 mm.
Palmer Guitar DI-box PDI09 A DI box designed especially for guitars, for use with line level preamps, or to be connected between amp and speaker, enabling direct-to-mixing-desk recording without microphones. Integrated filter circuits simulate the authentic "speaker" sound. Tone can be varied between "Mellow", "Normal", or "Bright".
Technical specifications:
Palmer Power Attenuator - Control the volume of your guitar amp
The PDI06 is a power attenuator for live applications. The device is connected between the amplifier output and the speaker cabinet. It makes it possible to use the popular power stage distortion of tube amplifiers while reducing the associated high volume level. This permits practical volume reduction in six increments from 100% to 18% for stage and practice room situations. An additional setting mutes the speaker completely; the PDI06 then functions as a LOAD BOX and absorbs the entire output power of the amplifier.
This mode of operation is useful, for example, when connecting an amplifier equipped with a speaker cabinet emulation directly to the mixing desk using an existing line-out and loud volume levels in the recording booth are undesirable. The unit has an input for the speaker signal from the amplifier and two outputs for connecting speaker cabinets.
The total impedance of the speakers must equal the value shown on the PDI06. For example: the outputs of a PDI06 that is specified for 8 ohms can be connected to one 8 ohm cabinet or two 16 ohm cabinets. The output of the (tube) amplifier is also set to 8 ohms.
Specifications:
Atténuateur de puissance Palmer - Contrôlez le volume sonore de votre amplificateur de guitare.
Le PDI06 est un atténuateur de puissance pour les applications Live. Il se place entre la sortie de l'amplificateur de puissance et le baffle. Il permet de bénéficier de toute l'intensité de la distorsion de votre amplificateur à lampes, sans pour autant devoir générer de niveaux sonores élevés. Le niveau sonore peut être ainsi réduit selon 6 valeurs, de 100% à 18%, ce qui peut être très pratique, sur scène comme en salle de répétition. Une position supplémentaire permet de couper complètement le haut-parleur ; le PDI06 travaille alors comme LOAD-BOX (boîtier de charge) et dissipe toute la puissance électrique générée par l'amplificateur.
Ce mode de fonctionnement est très pratique si vous désirez envoyer la sortie ligne de l'amplificateur (qui dispose d'une émulation de haut-parleur) directement dans la table de mixage, sans générer de bruit dans le local d'enregistrement. Le PDI 06 offre une entrée pour le signal au niveau haut-parleur issu de l'amplificateur et deux sorties pour le branchement de baffles.
L'impédance nominale du baffle (ou l'impédance résultante des baffles) doit correspondre à la valeur spécifiée sur le PDI 06. Exemple : Un PDI 06, réglé en position 8 Ohms, peut gérer sur ses sorties un baffle de 8 Ohms, ou deux baffles de 16 Ohms branchées en parallèle. La sortie de l'amplificateur (à lampes) est aussi réglée sur 8 Ohms.
Caractéristiques techniques :
Palmer Speaker Simulator The PDI03 combines reactive load, signal splitter and DI box in a 1 space 19'' rackmount unit. Especially designed for electric guitars and basses, all functions have been optimised for live and studio use. The PDI03 is directly connected to the speaker output of an amplifier eliminating the need to mic up a speaker cabinet. The special filters within the Simulator provide carefully contoured equalization, and the unit's signal is fed directly into mixing desk, tape deck or power amplifier etc. Particularly valve amps without master volume can be driven into saturation without being limited by volume. Amplifier noise and hum are greatly reduced to partically inaudible levels.
Two switches select between the 9 filter presets simulating various types of speakers and enclosures. Open back 2 x 12'' combo or 4 x 12'' cabinet characteristics and the punch of a full-out stack with a graphic EQ ''V'' setting can be selected as well as ''American'' or ''British'' speakers and ultra brightness. Four paralleled unfiltered outputs are available for further processing. Both filter and line out level are adjustable.
For live monitoring, speakers may be connected while the reactive load is automatically switched off. Power handling capacity is 100W RMS without speakers.
A splitter box with galvanic isolation which distributes a guitar signal to two amplifiers. Can be operated with a power supply unit (not included) or with batteries. "I always get a loud hum when I hook up both my amps...". A rather common problem! We've got the answer !! The Palmer Y-box's FET input circuitry adapts your guitar signal, driving a transformer which routes the ungrounded signal to the output. Ground hum is eliminated. 9V battery operation is recommended. The Y-box also serves as a line driver for long leads, and it allows for phase reversal of the AMP 2 output. This comes in handy when you're using two (pre-) amps.
Technical specifications: 6.3 mm Jack, input impedance: 1 meg. ohm Parallel AMP 1 output AMP 2 output electronically buffered, through transformer
Active, serial FX-Loop for a subsequent installation in an existing tube amplifier The FX-Loop works with two LND150 in the send and in the return stage. The send and return level can be adjusted to their optimal value with two potentiometers. The Loop works with the present high voltage of the amplifier. It has two inputs for low and high signal levels. Input Levels: InA: 30 - 60 Vpp, max. 65 Vpp InB: 10 - 15 Vpp, max. 18 Vpp
The FX-Loop utilize POTENTIALLY FATAL HIGH VOLTAGES. Seek help from a competent technician if you are in any way unfamiliar with high voltage circuits. Use at your own risk.
THIS IS NOT A KIT BUT A ASSEMBLED AND TESTED UNIT !
TT Parallel / Serielle Patch-Box
Everybody knows the problem: two speaker cabs but only one output - what do do ? Use the TT Parallel / Seriell Patchbox and you can connect two speaker-cabs in parallel or in seriell with your amp. Please watch the impedance !
The TT Z-Matcher is used to match the output impedance of an amp with the input impedance of a speaker cab. I will get pluged in between the out of the amp and the input of the speaker cab. Cover with black tolex. Input: 4-8-16 Ohms Output: 4-8.16 Ohms Power: 100 Watt max
The TT Z-Matcher is used to match the output impedance of an amp with the input impedance of a speaker cab. I will get pluged in between the out of the amp and the input of the speaker cab. Cover with Tweed Vinyl Tolex. Input: 4-8-16 Ohms Output: 4-8.16 Ohms Power: 100 Watt max
