Mains + Power

• for 2,1 x 5,5 mm plugs
• with switching contact
• Termination type: solder

• Diameter outside: 5,6 mm
• Diameter inside: 2,1 mm
• Depth: 27,0 mm
• Mounting hole: 11 mm
• Material: Metal
• Maximum current: 2A / 48 V DC

• compatible with plugs with 2,1 mm and 2,5 mm holes
• Pin diameter: 2,5 mm
• Working voltage: 12 VDC
• Maximum current: 5 A / 12V DC

• DC female, female, panel mount
• 0.5A 30 VDC, 3 pins
• Size 5.5 x 2.1mm
• Contact Resistance: < 0.03 Ohm
• Insulation Resistance: > 100 MOhm

• Inner Diameter: 2,1 mm
• Outer Diameter: 5,5 mm
• Shaft Length: 9 mm

Power Jack, Chassis mount

• different manufacturer
• Ratings IEC: 10 A / 250 VAC; 50 Hz
• Norm IEC320 / C14
• Betriebsspannung: 10 A / 250 VAC; 50 Hz
• Material: Housing PA6, black, UL 94V-0

Power Jack, Chassis mount

• Schurter 6162.0046
• Ratings IEC: 10 A / 250 VAC; 50 Hz
• Ratings UL/CSA: 15 A / 250 VAC; 60 Hz
• Dielectric Strength:    
  • > 3 kVAC between L-N
  • > 1.5 kVAC between L/N-PE (1 min/50 Hz)
• Allowable Operation Temp.:-25 °C to 70 °C
• Degree of Protection: from front side IP 20 acc. to IEC 60529
• Protection Class:Suitable for appliances with protection class 1 acc. to IEC 61140
• Material: Housing PA6, black, UL 94V-0

• with one fuse holders 5.0 x 20 mm
• Housing: polyamide
• for panel mounting
• Double-pole + protective ground 10 A/250 V
• single-pole fusing with bridge to the fuse holder at the L terminal
• fuse holder terminals for soldering

• up to T 70 °C
• with one fuse holders 5.0 x 20 mm
• Housing: polyamide
• UL 94 V-0, black
• for panel mounting
• Double-pole + protective ground 10 A/250 V
• single-pole fusing with bridge to the fuse holder at the L terminal
• fuse holder terminals for soldering
• Design to IEC/EN 60320-1
• fuse holder to IEC/EN 60127-6
• Certifications: ENEC, Semko, UL, CSA

• Power Jack with built-infuse holders 5.0 x 20 mm
• Housing: polyamide
• for snap-on mounting
• Double-pole + protective ground 10 A / 250 V
• single-pole fusing with bridge to the fuse holder at the L terminal
• fuse holder terminals for soldering
• Design to IEC/EN 60320-1

• with one fuse holders 5.0 x 20 mm
• Housing: polyamide
• for snap-on mounting
• Double-pole + protective ground 10 A/250 V
• single-pole fusing with bridge to the fuse holder at the L terminal
• fuse holder terminals for soldering

Power Supply chassis Socket,  with break contact and solder eyes, for front side mounting

• Diameter opening: 6,3 mm
• Diameter center pin: 1,9 mm
• Rated current: 0,5 A @ 12 V DC
• Isulation resistance: > 100 M Ohm